Konica Model Number 2230

• Changing Paper Size (trays)
• Adjusting Size (enlarge/reduce)
• Lighten/darken Copies:
• Loading Paper
• How to use 11 x 17 Paper:
• Loading Toner
• Taking a Meter Reading from the Copier:

Procedure: Changing paper size (trays):

1. Press the button under the digital panel that is farthest to the right. A new display screen will appear.
2. Press the button below the word "select" until you have selected the appropriate paper size. Then press the OK button.
3. To cancel, press the Reset button. (Reset will cause the copier to go back to 8.5 x 11 paper.)

Procedure: Adjusting Size (enlarge/reduce)

• Press the button under the digital panel that is second from the right. A new display screen will appear.
• To reduce, press the button below the down arrow. To enlarge, press the button below the up arrow. Then press the OK button.
• To cancel, press the Reset button.

Procedure: Lighten/darken copies

1. Press the button that is below the digital panel and second from the left. A new display screen will appear.
2. To lighten the image, press the button second from the left. To darken the image, press the button third from the left. Then press the OK button.
3. To cancel, press the Reset button.

Procedure: Loading Paper

1. After removing the paper from the package, open drawer 1 (top) for 8 x 11 or drawer 2 (bottom) for 8 x 14 paper.
2. On the right-hand side of the drawer (facing the copier) are two white plastic tabs that hold the paper in place. Make sure all the paper is under the tabs.
3. Close the drawer.

Procedure: How to use 11 x 17 Paper

1. Using the Bypass Tray

• Select the bypass option through the paper size selector.
• NOTE: For each sheet of 11 x 17 paper used, you will be charged for two copies.

2. Using the Second Drawer

• NOTE: The second paper drawer will support 8 x 11 , 8 x 14 and/or 11 x 17 paper.

• On the right-hand side of the drawer, the paper is held in place by two brackets. On the front bracket, lift the green tab and slide the brackets out.
• On the left-hand side of the drawer is a green bracket, which is held in place by one or two screws. Remove the screws, remove the bracket and place it in the slot farthest to the to the left and replace the screws.
• Load the 11 x 17 paper.
• Adjust the two brackets on the right-hand side until they fit snuggly against the paper. Close the drawer. The copier will know it is now loaded with 11 x 17 paper.

Procedure: Loading Toner

CAUTION: The copy machine will indicate when toner needs to be replaced. Never "top-off" toner or load it unless the copier indicates the toner needs to be replaced. If the copies are light, but the machine is not indicating that the toner needs to be replaced, please call 1-800-877-2679 for service.

WARNING: Before adding toner, carefully read the directions and safety information included with the toner cartridge. Keep toner away from children. Although toner is non-toxic, do not inhale it or allow it to enter your eyes. If toner comes in contact with eyes, consult your physician.

1. Open the front panel of the copier. The toner receptacle runs along the top of the copier.
2. On the left-hand side is a small green sticker. Swing the receptacle out and to the right.The toner bottle has a rectangular body and a square base.
3. The toner may have settled, so shake the new toner cartridge well before loading.
4. The base of the toner has an exterior plastic cap. Remove this cap.
   
   CAUTION: The toner bottle will also have an interior plastic cap. Do Not Remove the Interior Plastic Cap.
   
   
5. Along the base (opposite the label side) is a depressed lip. This fits under a similar raised lip on the toner receptacle.
6. Once the toner bottle is in place, slide the green lever forward.
   
   CAUTION: Do Not Squeeze the Toner Bottle. This can cause toner clouds and is difficult to clean up.
   
   
7. The toner bottle may take several minutes to empty. If some toner appears compacted at the top, gently tap the top or side of the bottle.
8. Once the bottle is empty, slide the green lever forward and remove the bottle.
9. Swing the toner receptacle back into place and close the front cover.

Procedure: Taking a Meter Reading from the Copier:

1. Open the front panel of the copier. The main meter is towards the upper, left-hand corner.
2. If the copier has a vend (coin) tower, TRM may ask for the cash or retail meter. This is usually located in the bottom left-hand corner.